- >License plate production line, car license plate cutting line, semi-finished license plate automatic production line, new energy vehicle license plate production line, small bus license plate automatic stamping line, label production line, embossing machine, hot stamping machine, reflective film, license plate aluminum coil
- >Punching machine, press machine, high-speed punching machine, forming machine
- >Fixed rotor production line, high-speed feeder, gear feeder, fixed rotor high-speed punch feeder, clamp feeder, high-speed servo feeder, filter stamping feeder
- >Anime manipulator, multi station stamping manipulator, multi station stamping forming manipulator, in mold transfer manipulator, in mold translation manipulator
- >2-in-1 feeding and leveling machine, 2-in-1 feeding machine, unwinding and leveling machine, automatic unwinding and leveling machine, unwinding and leveling machine
- >Welding robot, six axis robotic arm, stamping robotic arm, six joint robot, palletizing robot, polishing robotic arm, inspection robot, painting robot, stamping loading and unloading robotic arm, precision machining loading and unloading robot, bending robotic arm, die-casting and casting robot, packaging sorting robot, adhesive sealing robot
- >Laser cutting feeding line, roll material laser cutting automatic feeding line, laser cutting production line, laser cutting automatic feeding line
- >Kaiping Line, Unwinding Line, Automatic Kaiping Line for Roll Material, Cut Line for Roll Material to Size, Horizontal Cutting Line, Vertical Cutting Line, Roll Material Cutting Line, Cut Plate to Size Cutting Line, Automatic Feeding Line for Shear Plate Machine
- >Swing feeding machine, wafer dropping production line, barrel cover stamping swing production line, left and right swing coil automatic feeding machine, cross stamping swing feeding machine
- >3D robotic arm, multi station stretching and forming robotic arm, in mold stamping and lifting robotic arm
- >Three in one feeding machine, punch press feeding machine, roll material stamping automatic feeding machine, three machine integrated servo feeding line
- >Winder, Electroplating Automatic Winder, Etching Winder, Ultrasonic Cleaning Line Winder, Wire Drawing Production Line Winder, Film Coating Automatic Winder, Roller Coating Winder
- >Leveling machine, straightening machine, leveling machine, stamping finished product leveling machine, laser cutting workpiece leveling machine, precision leveling machine
Hubei Kuruidi Intelligent Equipment Co., Ltd
Contact phone number: 13797980475
Address: Tangyan Avenue, Jingshan City, Hubei Province
1: After the machines are transported to the customer's factory, they should be arranged in a straight line, and the two sections should be connected with screws, paying attention to the consistency of height. At the same time, the center line of the machine should be adjusted to be consistent with the center line of the mold.
2: In terms of wiring: Connect the previously removed wires one by one (according to the number tube), paying attention to the installation sequence of the sealing plate before and after. Reminder: The 4 sleeves coming out of the large electrical box should be paired one by one with the encoder wire plug, pulse wires Y0, Y1, 11,12, NC feeder motor wire, and large sleeve pipeline.
3: After installing all the circuits, please double check if they are installed properly and completely. After confirmation, install the machine seal board (precision leveling machine).
4: After confirming that the power switch of the electrical box control panel is in the disconnected state, turn on the power supply (3-phase 380V), turn on the power switch, confirm if it is normal, and immediately cut off the power if there is any abnormality.
5: Operate the control handle and press (rack up) or (rack down) to adjust the material discharge height to be level with the mold. Be careful to loosen the screws of the NC feeder frame, otherwise the action will be ineffective. (There are three limit switches, the top limit switch is the main control, the middle limit switch is the upper limit, and the bottom limit switch is the lower limit.)
6: Finally, connect the feeding and relaxation signal lines of the machine to the punch press (three lines X7, X4, COM), and also connect the emergency stop line (two lines 65 and 66) as needed.
7: After everything is confirmed to be normal, the three in one feeding machine can enter normal production. Pay attention to safety and regularly check and add lubricating oil.